|
| Ticket # | Date/Time | Question |
| 197153 | 7/6/2010 6:12:07 PM | I have 45 amp charging system. Will this regulator work or do you have another that will?
ELECTRONIC VOLTAGE REGULATOR
ACCEL Chrome Electronic Voltage Regulators for Harley-Davidson applications do not require any re-wiring or special mounting. Heavy Duty solid-state circuitry and years of technology produce a regulator that has quality second to none and reliability that you can depend on year after year. They are made in the U.S.A. and are covered by a limited replacement warranty. OE#: 74505-97, APPLICATION: 1997-2001 FLHT, 1999-2001 ... |
| 191703 | 1/16/2010 10:39:47 AM | I purchesed you self learning control module, I'm having a hard time mounting the module as per the instructions, and ending up with the wires being long enouph to us the factory looms. Can you send me photos as too where the module should be mounted. It's the SLM05. Thanks. |
| 191230 | 12/23/2009 1:41:21 PM | What kinf of regulator should I use for this bike.
Thank you. |
| 191183 | 12/21/2009 4:35:15 PM | I am looking for an aftermarket set of coils and wires that will work with my 81 Yamaha XS1100 Special, could you recommend the coils that will work with my bike. I am just not sure which ones I need, would also prefer black if possible.
Thank you in advance
Chris |
| 191182 | 12/21/2009 4:10:23 PM | What is the outside diameter and width of the rotor/fly wheel of your 38 Amp charging system? I want to know if it will physically fit inside my engine cases. |
| 191045 | 12/14/2009 9:59:12 PM | I have a single fire ignition system on my 99 softail, but still run in in dual-fire mode. If I wanted to switch it to single-fire, do I have to install TWO of your single-fire coils (#140408)? |
| 191016 | 12/14/2009 7:04:53 AM | What is a " F1- Light " ? |
| 190711 | 11/30/2009 2:17:33 PM | a few months ago I put a new accel distributor in my car (part #59107c) It worked fine but the idle would not slow down unless I draged it down. The garage put another set of springs on the weights. It was a lot better but still did this once in a while. Lately it started to cut out at higher rpms with a drag on the engine(up hill verses down hill. It is not a fuel problem. Now when it starts this ,it usually keeps getting worse to the point the car will hardly run. I have been told the weights in the dist. are sticking. What are your thought... |
| 190125 | 11/5/2009 4:52:27 PM | What is the warranty period on the fuel injection Self Learning Module ??? How are warranty returns handled (back to original retail or directly with Prestolite? Thanks! Jeff |
| 190055 | 11/3/2009 8:58:13 AM | What should the secondary resistance be for accel coils #140403 measured between the high voltage outputs? |
| 162804 | 7/20/2007 11:09:17 AM | Just purchased #35496 ignition set up for single fire what settings on the ignition shoud i be using |
| 106887 | 8/26/2004 1:07:59 AM | I bought a NEW ACCEL PETCOCK to replace damaged petcock on my motorcycle. I missplaced (LOST) ACCEL PETCOCK GASKET to gas tank and can not locate another gasket. Can you sell me a replacement gasket? if not where can I find one? THANK YOU |
| 96144 | 2/18/2004 9:43:09 PM | I have a gasket set #38443. This set has steel type cyl base gaskets and rocker box gaskets.They seem to have a coating on them.Do I need to apply a gasket sealer to the steel gasket?Can you give me a web site that I can show my customer because he thinks that James gaskets are the way to go.I do-not have a catalogue of my own I get your product from Preston Cycle Products. Thanks for your time.Kanally,s Engine Service. |
| 92264 | 12/30/2003 6:42:13 PM | I would like to upgrade my coils with accel coils. Could you recommend a set. Thanks JC |
| 87044 | 8/30/2003 11:55:26 AM | How to adj. voltage regulator # 201105 & 201105C OEM # 74510-64
Problem: Replaced battery,and generator. when checking charging system at 3000 RPM., found voltage at battery 15volts and current from armature to regulator 18amps.
generator mfg. recomends not exceeding 10amps draw from gen.
thank you
SM |
| 83409 | 7/5/2003 6:58:37 PM | Does mallory have coils and wires for the Z1 ? |
| 54067 | 9/14/2002 4:15:53 PM | I have the stock electrical system of generator,v/reg, points, condensor and coil. I would like to get away from this set-up, mainly, and you're going to laugh, because I've had this same bike for 23 years and my eyes aren't as good as they used to be for adjusting points. Any suggestions would be appreciated.
Joe Gyde |
| 31542 | 2/28/2002 12:32:12 AM | Do you make a hot coil & plug wires for my 99 fuel injected RoadKing?Regards,TomKelly |
| 31259 | 2/24/2002 9:58:34 AM |
Hello,
My name is Chris and I need to find some spark plug wires for my bike. H-D changed the coil on the 2000's so they use a long straight boot at the coil. I can't seem to find aftermarket wires. Can you bail me out of a jam? Thanks for your time.
CHRIS |
| 31248 | 2/23/2002 10:30:44 PM | Where can I find the "Accel 300+ Race Wire" for my 2001 Road King. I have not seen these advertised in catalogs. |
|